Lowering costs with sophisticated tool solutions

Precision tools influence overall operating costs in various ways. First, and most obviously, there are the costs of the tool itself: the costs of purchasing and using the tools, including the cost of non-productive time – for example, when a tool needs to be replaced. But on top of this, cleverly designed tools have an impact on investment costs. For example, a customer might be able to avoid buying a new machine if suitable tools allow the machining to be carried out on their existing machines. Similarly, increased machine productivity reduces the number of machines that need to be purchased. It might even be possible to replace a special machining process by using the right tool. Process reliability is another factor on which tools can have a significant impact – for example, by avoiding the need for measuring tasks. And finally, gains can be made on rationalisation and cost-reduction when it comes to services, particularly in logistics, storage, and employee training.

Combination tools are the classical example for a direct reduction in operating costs. This is
demonstrated in the following example from the car industry: A transmission housing made of the cast aluminium alloy AlSi9Cu3 was machined on a standard machining centre with a hollow shank taper connection. More specifically, the process involved the drilling of recesses in the variable valve timing (VVT) system. The most important concern was the accuracy of the large diameter during cutting. The shape is pre-cast, requiring a stock removal of 2 – 4 mm. There is no pre-machining. In terms of tool design, the customer’s aims were

• to carry out the machining with as few tools as possible
• to increase productivity by combining tools
• to simultaneously maintain maximum weight and moment-of-tilt requirements

Due to its thin walls, the part was prone to vibration during machining. In combination with extreme length-to-diameter proportions, complicated shape characteristics, necessary control cuts, and tolerances in the IT6 range, the machining process placed high demands on the tool technology.

In contrast to the competition, MAPAL was able to achieve the machining with just one combination tool. With the tool’s lightweight construction, the weight and moment-of-tilt requirements are not a problem. The cycle time is also reduced; the annual production time saved amounts to a total of 833 hours. Based on machine operating costs of 100 euros per hour, the operator saves over 83,000 euros annually.

The machining of the tube sheets for shell and tube heat exchangers demonstrates how tool design can have an impact on process reliability costs. The tube sheet forms the end of the bundle of tubes in the heat exchanger. Depending on the size of the heat exchanger, it may have a large number of bores – often as many as several hundred. In order to ensure that the fluid medium does not escape at the point of connection between these parts, the bores have high positional and dimensional accuracy requirements. Because of the tolerance requirements and the cost of solid drilling operations, the choice of tool has an especially high impact here.

MAPAL’s three-bladed TTD-Tritan replaceable head drill demonstrates its full potential in this application. Due to its limited use of cost-intensive solid carbide, the replaceable head system represents resource e¡ciency and reduced inventory costs. At the same time, it achieves the performance level of a solid carbide drill. For this application, every machining diameter is required at multiple lengths. In this case, the separate provisioning of drill heads and tool holders has a further positive impact on inventory costs.

For example, the TTD-Tritan achieves significant improvements compared to the previously used double-edged tool from a competitor when machining tube sheets made of SA-516-70N high-carbon steel with a diameter of 25.6 mm and a bore length of 63.5 mm. The replaceable head drill reduces machining time by 57 percent: the MAPAL tool needs only 29 minutes to complete 550 bores. These benefits are a result of the TTD-Tritan’s 59 percent higher feed rate on the one hand and an improvement of the process on the other: users no longer need to pilot or subsequently clean the part. In addition to this, the TTD-Tritan improves the direct machining costs, as the three-bladed replaceable head drill has a 90 percent longer tool life than the competing tool.

Reib- und Feinbohranwendungen mit extrem hohen Anforderungen an Form- und Lagetoleranzen sind das Hauptanwendungsgebiet von Führungsleistenwerkzeugen. Ihr Vorteil: Die Präzisionsschneiden sind µm-genau in Durchmesser und Verjüngung einstellbar. Ihr Nachteil: Die Schneiden müssen in Durchmesser und Verjüngung eingestellt werden. Diese Einstellvorgänge nehmen Zeit in Anspruch und setzen Know-how beim Bediener voraus. Mit der Entwicklung des EasyAdjust-Systems trägt MAPAL diesem höheren Aufwand Rechnung. Ein hochpräzises Justiersystem mit Kassette und voreingestellter Verjüngung ersetzt einen der beiden Einstellvorgänge. Die Präzision bleibt gleich, das Handling ist einfacher.

In einem Anwendungsbeispiel ist eine Außenreibahle mit Innendurchmesser 75 mm mit dem EasyAdjust-System ausgestattet. Die Reibahle bearbeitet Zapfen an Planetenträgern aus Vergütungsstahl. Die Zapfen haben bei 75 mm Durchmesser eine Toleranz von 18 μm, die maximale Abweichung der Zylinderform beträgt lediglich 5 μm. Speziell bei Außenreibahlen entfaltet sich das Potenzial des EasyAdjust-Systems. Denn die Einstellelemente sind bei Außenreibahlen schwer zugänglich und erschweren so zusätzlich den Einstellprozess. Der Wegfall der Verjüngungseinstellung macht sich daher stark bemerkbar. Die hohe Präzision kombiniert mit einer wirtschaftlichen, vierschneidigen TEC-Wendeplatte sorgt für maximale Wirtschaftlichkeit der Bearbeitung: Auf einem Bearbeitungszentrum arbeitet die Außenreibahle mit einer Schnittgeschwindigkeit von 120 m/min und einer Vorschubgeschwindigkeit von 60 mm/min. Eine Schneidkante bearbeitet dabei 470 Zapfen. Erst nach 1.880 Zapfen kommt eine neue Wendeschneidplatte zum Einsatz.

By now, the advantages of digital connectivity are well-known. In cutting manufacturing, too,
digital possibilities have become an indispensable driving force in the overall operating costs. Nevertheless, the investment and start-up costs of digital services are often a hurdle for companies that carry out machining. Ultimately, their implementation in existing manufacturing processes often involves factors such as the need to modernise the available machinery or carry out new installations.

With c-Connect, the open-cloud platform c-Com offers a simple and economical way of networking machines. c-Connect makes it possible to digitally transfer tool measurement data from the setting fixture to the machine, registers inventory changes, and is able to monitor the machine status via various sensors and the c-Connect box. Simply, compatibly, and quickly. Operators benefit from cost-saving results immediately. Here are just some of the benefits:

• no chance of errors resulting from the manual inputting of tool data;
• information concerning the tools, such as their tool life, remains available after the tools have been removed;
• transparent data is available to all persons involved;
• machine downtimes are minimised.

MAPAL’s tool specialists are continuously developing product and process solutions with the
aim of achieving maximum cost-eœectiveness for their customers. With 70 years of experience, a broad range of products, and a global presence, the precision tools manufacturer offers customers future-proof and technologically leading solutions: “When looking at the overall costs, there are a lot of ways in which our tools can make a difference. For that reason, our technical advisors always design the tools specifically for each individual customer – and oœer a service warranty that we are able to fulfil optimally through our global service network”, emphasises Siegfried Wendel. “With the right technological partner at your side, completely new opportunities for cost savings become available.”